Welcome to the PiMP Mining Community Forum.


Coin/crypto news, miner.farm and getpimp.org announcements, guides, and tips.


setting clocks in pimp OS 1.9 fglrx



  • As​ ​we​ ​have​ ​learned​ ​gputool​ ​will​ ​not​ ​run​ ​with​ ​the​ ​old​ ​cards​ ​that​ ​use​ ​the​ ​fglrx​ ​drivers.

    But​ ​this​ ​does​ ​not​ ​mean​ ​that​ ​you​ ​can't​ ​adjust​ ​the​ ​setting.

    BEFORE​ ​UNDERTAKING​ ​THERE​ ​ARE​ ​NO​ ​SAFEGUARDS​ ​IN​ ​PLACE
    PLEASE​ ​READ​ ​THE​ ​BELOW​ ​BEFORE​ ​STARTING​ ​OVERCLOCKING!!!!!!

    AS​ ​WITH​ ​ALL​ ​OVERCLOCKING​ ​TOOLS​ ​YOU​ ​ARE​ ​ENTIRELY​ ​RESPONSIBLE​ ​FOR​ ​ANY
    HARM​ ​YOU​ ​MAY​ ​CAUSE​ ​TO​ ​YOUR​ ​HARDWARE.​ ​OVERCLOCKING​ ​CAN​ ​INVALIDATE
    WARRANTIES,​ ​DAMAGE​ ​HARDWARE​ ​AND​ ​EVEN​ ​CAUSE​ ​FIRES.​ ​THE​ ​AUTHOR​ ​AND
    PIMP​ ​LLC.​ ​ASSUMES​ ​NO​ ​RESPONSIBILITY​ ​FOR​ ​ANY​ ​DAMAGE​ ​YOU​ ​MAY​ ​CAUSE

    lets​ ​start​ ​simple​ ​just​ ​adjust​ ​the​ ​intensity,​ ​shaders​ ​and​ ​​ ​thread-concurrency.

    intensity​ ​:
    how​ ​hard​ ​can​ ​your​ ​card​ ​work​ ​setting​ ​this​ ​setting​ ​goes​ ​from​ ​0​ ​to​ ​31​ ​and​ ​when​ ​it​ ​is​ ​set​ ​to​ ​high
    it​ ​will​ ​cause​ ​more​ ​Hardware-errors​ ​and​ ​actually​ ​causes​ ​you​ ​to​ ​mine​ ​slower

    shaders​ ​:
    here​ ​you​ ​can​ ​tell​ ​the​ ​miners​ ​how​ ​many​ ​shaders​ ​are​ ​on​ ​your​ ​card​ ​and​ ​how​ ​many​ ​can​ ​be​ ​used
    this​ ​​ ​is​ ​card​ ​specific

    thread-concurrency.
    Setting​ ​thread​ ​concurrency​ ​overrides​ ​anything​ ​you​ ​put​ ​into​ ​--shaders​ ​and​ ​is​ ​ultimately​ ​a
    BETTER​ ​way​ ​to​ ​tune​ ​performance.

    When​ ​changing​ ​these​ ​settings​ ​please​ ​just​ ​increase​ ​them​ ​step​ ​by​ ​step​ ​and​ ​run​ ​the​ ​miner
    every​ ​time​ ​​ ​you​ ​make​ ​a​ ​change.

    This​ ​should​ ​increase​ ​the​ ​speed.

    For​ ​the​ ​peeps​ ​who​ ​need​ ​more​ ​out​ ​of​ ​there​ ​cards​ ​​ ​there​ ​are​ ​2​ ​other​ ​settings​ ​to​ ​tune
    gpu-engine​ ​and​ ​gpu-memclock​ ​but​ ​before​ ​adjusting​ ​these​ ​please​ ​read​ ​the​ ​fat​ ​warning​ ​above again.

    ​ ​LOOK​ ​AT​ ​MANUFACTURER​ ​SITE​ ​FOR​ ​DEFAULT​ ​CLOCKS​ ​AND​ ​START​ ​WITH
    THOSE

    In​ ​your​ ​conf​ ​of​ ​in​ ​this​ ​case​ ​the​ ​sgminer-gm​ ​you​ ​need​ ​to​ ​add​ ​these​ ​values​ ​because​ ​they​ ​are
    not​ ​there​ ​by​ ​default.

    1.“gpu-engine”​ ​:​ ​“engineclock”, (engine​ ​clock​ ​is​ ​the​ ​clockspeed​ ​the​ ​core​ ​will
    take)
    2.“gpu-memclock”​ ​:​ ​“memoryclock”,(memory​ ​clock​ ​is​ ​the​ ​clockspeed​ ​the​ ​memory
    has​ ​on​ ​the​ ​card)

    EXAMPLE

    first​ ​a​ ​basic​ ​run​ ​random​ ​card​ ​with​ ​added​ ​values​ ​of​ ​clocks​ ​and​ ​a​ ​screenshot​ ​of​ ​the​ ​hash
    speed.

    0_1508189787015_settings miner slow.jpg

    0_1508189798530_running miner slow.jpg

    seccond​ ​the​ ​same​ ​basic​ ​run​ ​random​ ​card​ ​with​ ​higher​ ​clock​ ​speeds​ ​and​ ​a​ ​screenshot​ ​of​ ​the
    hashspeed.

    0_1508189808053_setting miner bit faster.jpg

    0_1508189834142_running miner bit faster.jpg

    Final words
    start with default changes before changing clocks.
    find clock speeds for your card(s) and put them in.
    (separate with , if you have multiple cards and clocks )
    final don't go quick and check every time and TAKE TIME FOR THIS!!


 



Want 10% more hash from your rigs?



We promise to keep your email safe and never spam you.



Copyright (c) 2012-2019 Portable Instant Mining Platform LLC. All rights Reserved.