Welcome to the PiMP OS and Miner.farm forum.
How to Write the PiMP OS Image using Windows
Update! Check out this video Flashing PiMP OS v2.6 Image from Windows the Fastest and Easiest way using HDD Raw Copy:
To start, you'll need a copy of HDDRawCopy
Note: You can also write the image from Windows with DMDE program. See below comments section for a guide from our Testing/Support team member, blackice!
After you've successfully installed the program, you should see this screen:
Select the correct file, click continue and find the OS image file.
Click open, then select it and press continue for the next step.
A new window should pop up that says "TARGET" across the top.
On this screen, you will selet the SSD or HDD that will go in your rig. If you are unsure which drive to pick, open your explorer and go to THIS PC (Windows 10) and look for the drive there.
For this example, we are going to work with the disk drive "test", which is
Drive G:. We take the drive letter (
G) and find it in the HDDRawCopy tool.
Select the drive, and click continue. A new screen will pop up with a
Startbutton. When you are sure that your source and your target are correct, click
A warning will popup, the computer asking for you to confirm because everything that was on the disk will be overwritten. If you are sure, click yes.
The process will begin, and it is important that you do not close the program or turn off the PC until the process is complete. When the program is done writing the image to the disk, you should see task complete and a 100% complete
Once the process is complete, you may shut down the program, turn off your PC, and once everything is powered down, you can remove the SSD or HDD and put that disk in your rig. Boot the rig using the drive that you wrote from your workstation.
Also, if you do not succeed with HDDRawCopy, you can use an excellent tool - DMDE.
Push Tools -> Copy Sectors... or just a combination of Alt + W buttons on the keyboard.
As a source, you must select .img file of PiMP OS.
It will look like this:
You must select a physical Device as the destination.
Attention! You need to select an empty Physical Device, specially connected to the PC to record PiMP image and not any other :) Well, now you can click Ok.
You must confirm the overwriting by clicking Yes
Just wait a few minutes.
Congratulations! SSD with your fresh pimp is looking forward to connect in your new shiny rig!
Do not forget to unmount, eject, close that drive!
Remember that you want a CLEAN image. That means close the drive out before removing it from the imaging machine. Normally, you would use the OS tools to 'Eject' or ''Unmount' the drive from your operating system. This closes up device, flushes the buffers, and makes sure its all nice and tidy. We have noted a number of folks with license key issues after a fresh image because the drive is dirty on boot. So take the extra step here and make sure you 'Eject' and/or 'Unmount' the imaged drive!
jdbgo2shop last edited by
I'm not a novice with linux how ever I've tried everything listed here, including fresh formats and etc etc multiple different combos to get a copy working how ever I'm not having very much success... have tried using different storage systems ie ssd , sd, usb , have trying different methods ie dmde, hdd, rufus etc etc. and multiple different variateions. any help ?
And what is your issue? Can you make post in Troubleshooting section https://forum.getpimp.org/category/8/troubleshooting with logs, errors, screenshots etc.? This will help to understand the problem and solve it. Thanks.
Sometimes, we try to hard :). The process is simple. Just bit for bit copy the image to an ssd. All the methods you are trying above place an image with a boot agent. Think more along the lines of how you would make a raspberry pi bootable sd card, vs burning a live iso to a thumb drive.
desfletc last edited by desfletc
This post is deleted!
Here is an alternative method using win32diskimager. This works for disks that are connected via USB and already have a drive letter visible to Windows.
Run the exe:
If it sees the drive letter, make sure it is the right one!!!! And then pick the pimp img file that you unzipped and then click Write.
Anything other than this? It didn't write properly....
doug last edited by
Can I put it on a thumb drive in windows then boot that on my rig and put it on the ssd in the rig so it boots from there?
@doug You can juggle an image as you like. But you need to write it down in one of the recommended ways.
anotherjoe last edited by
This post is deleted!
ralph.halgas last edited by
I did exactly as prescribed over here (btw my 16gb wasn't big enough, had to buy 32 gb!) and then I tried to boot my asus b250 mining expert (having enabled compatibility boot in Bios - I know that much!) and it won't boot at all... Why??!
There are no messages. It just won't boot. The hard drive is visible under UEFI bios and it is recognised as bootable.
Some cheap 16GB SSDs are not really 16GB. Like Kingdian is really only 15.8 or so.
When it doesn't boot at all, there can be so many possible things. We will need more information on how your BIOS is setup etc. Would recommend following some of the many well written guides on setting up the BIOS for PiMP.
Then post the values for those settings if you are having further issues. Double check all the wiring, etc. Reduce things down to just one GPU to start.
nicolman last edited by
Hi . Ok but after charging the source.image with DMDE ! how to start the miner ? watt is the process to start ?
Check out the Quickstart Guide
nicolman last edited by
Ok I try this : ssh firstname.lastname@example.org but I find : ssh: connect to host 10.0.0.193 port 22: No route to host . I'm on Linux
This type of assistance would be best to get from the Discord Pimp channel Here
Join the channel and ask your questions. Someone is almost always on that can assist you.
Updated original post with video. Thanks again!
We promise to keep your email safe and never spam you.
Copyright (c) 2012-2018 PiMP LLC. All rights Reserved.